Online only

RGB LED Strip 24V-7.2W/m-IP65-5m roll

HL-LS5050-30RGB-IP65-24V

New product

RGB LED strip, 24V, IP65 (Waterproof)

30 LEDs/m–7.2W/m–540Lm/m

5m roll–10mm width

3 year warranty

More details

15 Items

Same Day Dispatch

£ 35,00 excl. VAT

£ 7,00 per Meter

Add to wishlist

Data sheet

LED Chip SMD5050
Voltage 24V DC
Colour RGB
Power 7.2 W/m
Brightness 540 Lm/m
Number of LEDs per meter 30
Rating IP65 (Splashproof)
Width of strip 10mm
Cutting length Every 5 LEDs (168mm)
LED Strip Packing 5-meter roll
Voltage Type Constant Voltage
Warranty 3 Years
Brand Hi-Line

More info

Commercial high grade RGB LED strip

7.2W/m – 24V DC – 5m roll – 30 LEDs/m – IP65 (Waterproof) – 4-wire cable (15cm on each side of the strip roll)

The RGB LED strips are powered by high quality quad SMD5050 LED chips which generate a brightness of 540Lm/m and vivid colours.

The strip can be cut every 5 LEDs (168mm). The width of the LED strip is 10mm.

Fitted with an easy to install original 3M adhesive tape with excellent adhesion also under water (identified by a red protective strip on the adhesive side).

IP65 Waterproof Protection (IP65 = Splashproof) is achieved with polyurethane and silicon, which is the most expensive and best method that can be used on LED strips. This waterproof protection is very durable and does not become "yellowish" as it happens with most LED strips within 3 months of installation. Moreover, the LED strip remains extremely flexible, very clear, soft and well-protected throughout its life time and can keep its IP65 rating for more than 5 years if installed using an aluminium LED profile (to run at lower temperatures). Please note that IP00 rated LED strips are recommended wherever IP65 rating is not required (e.g. in indoor spaces) as these are easier to handle and install.

3 year warranty

______________________________

The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.

Please do NOT connect more than 10 meters of a LED strip in series. A LED strip of more than 10 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Thus, when 10 meters of LED strip are exceeded, it is suggested to connect both ends of the strip directly to the LED controller using a 4-core cable.

Please note that this data is based on the average readings for a 5-meter long LED strip. If the length of the strip is 1 meter the power consumption will be higher as there is almost no voltage drop. For comparison, the test result for 1m RGBW LED strip with 14.4W and 60 LEDs showed a power consumption of 18.48W or 0.77A.

Installation hints and tips for LED strips can be downloaded at the bottom of this web page.

_____________________________

The RGB LED strip comes with a 15cm wire ending (4-core) on each side of the strip roll.Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).

Please note that soldering is recommended for the connection of LED strips. However, if a solder-free connection is preferred, Hi-Line’s solder-free connectors offer the best solution currently available on the market.

______________________________

All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.

All Hi-Line RGB and RGBW LED strips are fully compatible with Fibaro RGBW LED Controller, Rako or ANY common anode LED controller available on the market.

______________________________

The stated price is for 1 x 5-meter roll RGB LED strip with 150 SMD5050 LEDs – IP65 (Waterproof), 24V DC.

______________________________

Selection of the LED driver depending on the maximum LED strip length

The table below shows the maximum LED strip length, which can be operated with a given LED driver.

To consider the performance drop, which occurs in the power supply cable and the efficiency of the LED Driver, 20% were deducted from the maximum strip length in the table below.

Note that, for driving RGB LED Strips, you will have to combine the LED Driver with a RGB/RGBW LED Controller.

In such case, LED driver is not required to be dimmable. Brightness control (dimming) and colour adjustment is still possible through the LED controller.

Reviews

No customer reviews for the moment.

Write a review

RGB LED Strip 24V-7.2W/m-IP65-5m roll

RGB LED Strip 24V-7.2W/m-IP65-5m roll

RGB LED strip, 24V, IP65 (Waterproof)

30 LEDs/m–7.2W/m–540Lm/m

5m roll–10mm width

3 year warranty

Customers who viewed this item also bought

Download

UK - LED Installation manual

Advice on the LED strip installation

Download (1.15M)

UK - Specification Sheets

HL-LS5050-30RGB-IP65-24V Specification Sheets

Download (221.48k)