Online only

Natural White LED Strip 24V Constant Current-14.4W/m-IP00-CRI70-SMD2835

HL-CC2835H-60NW-IP00-24V

New product

Natural White LED strip, 4000K, 24V, Constant Current, IP00 (Non-Waterproof)

60 LEDs/m–14.4W/m–1320-1440Lm/m

10m roll–8mm width

3 year warranty

More details

This product is no longer in stock

£ 60,00 excl. VAT

Add to wishlist

Data sheet

LED Chip SMD2835
Voltage 24V DC
Colour Natural White
Power 14.4 W/m
Brightness 1320~1440 Lm/m
Number of LEDs per meter 60
Rating IP00 (Non-waterproof)
Colour Temperature (CCT) 4000K
Colour rendering (CRI in ra) 70
Width of strip 8mm
Cutting length Every 6 LEDs (100mm)
LED Strip Packing 10-meter roll
Voltage Type Constant current
Warranty 3 Years
Brand Hi-Line

More info

Note: This product is being phased out. An upgraded version with CRI>80 is now available. Please click here.

Commercial High Grade Natural White LED Strip 4000K

14.4W/m – 24V DC – 10m roll – 60 LEDs/m – IP00 (Non-Waterproof) – 2-wire cable (15cm on each side of the strip roll)

This is a brand new technology single colour LED strip, which operates with constant current, meaning that it can produce very high brightness at low drive currents. Therefore, it is possibly the brightest product available today with a consumption of only 14.4 Watt per meter. Please note that 2 meters of this LED strip have better results than a 4ft fluorescent tube.

This very high brightness LED strip is powered by high quality Epistar SMD2835 LED chips which generate a brightness of 1320-1440Lm/m.

Note: This LED strip can operate with 23V DC to 24V DC (due to ICs that keep the chip current constant). That way the voltage drop will not affect the brightness or operating life of the LED chips. This strip can be connected with constant voltage 24 Volts DC LED Drivers, no special drivers are required.

This LED strip can also be connected to any 24V PWM controller (DMX Dimming or analogue) same as normal LED strips.

Excellent colour rendering index (CRI) – all LED chips reach a value of Ra >70.

The strip can be cut every 6 LEDs (10cm). The width of the LED strip is 8mm.

Fitted with an easy to install original 3M adhesive tape with excellent adhesion.

3 year warranty

______________________________

The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.

Please do NOT connect more than 10 meters of a LED strip in series. A LED strip of more than 10 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Please note that 10m of this product can be installed in a single run with power only fed from one side. Thus, when 10 meters of LED strip are exceeded (for up to 20m), it is suggested to connect the strip to a 24V DC power supply in the middle of the run (leaving 10 meters of LED strip to the left and 10 meters to the right).

Please note that this data is based on the average readings for a 5-meter long LED strip. If the length of the strip is 1 meter the power consumption will be higher as there is almost no voltage drop. For comparison, the test result for 1m RGBW LED strip with 14.4W and 60 LEDs showed a power consumption of 18.48W or 0.77A.

Installation hints and tips for LED strips can be downloaded at the bottom of this web page.

_____________________________

The LED strip comes with a 15cm wire ending on each side of the strip roll.Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).

Please note that soldering is recommended for the connection of LED strips. However, if a solder-free connection is preferred, Hi-Line’s solder-free connectors offer the best solution currently available on the market.

______________________________

All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.

______________________________

The stated price is for 1 x 10-meter roll LED strip (Natural White) with 600 SMD2835 LEDs – IP00 (Non-Waterproof), 24V DC Constant Current.

______________________________

Selection of the LED driver depending on the maximum LED strip length

The table below shows the maximum LED strip length, which can be operated with a given LED driver.

To consider the performance drop, which occurs in the power supply cable and the efficiency of the LED Driver, 20% were deducted from the maximum strip length in the table below.

Note that LED strips dimming is possible if the driver is used in combination with an LED controller. In such case LED driver is not required to be dimmable and brightness control (dimming) is still possible through the LED controller.

 

Reviews

No customer reviews for the moment.

Write a review

Natural White LED Strip 24V Constant Current-14.4W/m-IP00-CRI70-SMD2835

Natural White LED Strip 24V Constant Current-14.4W/m-IP00-CRI70-SMD2835

Natural White LED strip, 4000K, 24V, Constant Current, IP00 (Non-Waterproof)

60 LEDs/m–14.4W/m–1320-1440Lm/m

10m roll–8mm width

3 year warranty

Customers who viewed this item also bought

Download

UK - LED Installation manual

Advice on the LED strip installation

Download (1.15M)