Your cart
There are no more items in your cart
How to Cut and Connect IP67 Waterproof LED Strip
Commercial IP67 LED strip is not DIY clip tape. Use the two factory tails on each 5 m roll, cut only on the marks, seal ends with 12 mm silicone caps, and solder only extra power joins.
Read moreLutron DMX512 Case Study: RGB+CCT COB Cornice Lighting in Two Zones
Typical two-zone cornice job with Lutron. RGB+CCT COB (not RGB-only), 14 m + 10 m, 5-channel DMX decoders and 300 W drivers. What we can supply if your installer adds a Lutron DMX512 gateway.
Read more14m 30mm Ultra-Bright COB LED Strip (40W/m) – Mains Dimming with Independent 5m Sections
How to install a 14 metre 30mm ultra-bright COB LED strip at 40W per metre with mains dimming. Three electrically independent sections (5m + 5m + 4m) that look like one line, using one 300W hybrid driver and one HL-S1-A booster per section.
Read moreOutdoor LED Installation & Warranty Guide
Outdoor LED lighting systems operate in harsh environmental conditions including rain, flooding, condensation, UV exposure, insects, chemicals, and temperature changes. This guide explains the realities of outdoor LED installations, including maintenance expectations, IP ratings, installer responsibilities, environmental limitations, and warranty considerations. Learn why professional installation, correct waterproofing, and regular inspection are essential for reliable long-term outdoor lighting performance.
Read moreDMX512 Cable Guide: Correct Wiring, Device Limits, Splitters and Best Installation Practice
DMX512 is widely used to control LED lighting, stage lighting and architectural lighting systems. Using the correct cable type, proper wiring and following installation rules such as the 32 device limit per DMX chain are essential for reliable operation. This guide explains the correct DMX cable types, the use of Cat5 cable, and why splitters and terminators are important in professional DMX installations.
Read moreHow to Choose the Correct Remote for the HL-V5-L(WT) Wireless LED Controller
Guide explaining how to select the correct remote control for the HL-V5-L(WT) wireless LED controller. The controller can operate different LED strip types using DIP switch configuration, so the remote must match the LED strip type (Single Colour, CCT, RGB, RGBW, or RGB+CCT). Always check the Related Products tab on the LED strip product page to find compatible remotes or wall panels, and refer to the Attachments tab for the controller manual showing the correct DIP switch settings.
Read moreMulti-Zone Addressable RGBW Pixel LED System – Mirrored Animation Architecture
Multi-Zone Addressable RGBW Pixel LED System Technical example of a 12V SK6812 RGBW addressable pixel installation engineered for synchronised mirrored animation across multiple strip runs. The system utilised parallel SPI signal distribution, independent power supplies per zone and pre-configured bench testing to ensure stable voltage, correct data direction and uniform animation timing. Total system size: 983 individually controllable pixels across approximately 17 metres. Suitable for retail, architectural and commercial pixel lighting applications.
Read moreHow to Handle 90° Corners with IP68 Outdoor RGBW LED Strips
90° Corners with IP68 Outdoor RGBW LED Strips With fully sealed IP68 outdoor RGBW LED strips, 90-degree corners should not be done by sharply bending the strip or creating on-site corner joins, as this can compromise the factory waterproofing. The most reliable method is to install separate straight runs: One strip finishes before the corner, and a second strip starts after the corner. Both cut ends are sealed properly using end caps and silicone. This gives a clean corner appearance without introducing a waterproof joint directly at the turn. On-site soldering is technically possible but requires extreme precision, as RGBW strips have five closely spaced conductors and must be professionally resealed back to full IP68. Once the lengths and layout are confirmed, we are happy to help size the correct power supplies, controllers, and control options for the full system.
Read moreClick & Collect (Order Collection) Policy – Please Read Before Ordering
Click & Collect – Important Information Hi-Line Lighting offers Click & Collect from our single collection point: Big Yellow Storage, 163 London Road, Kingston upon Thames, KT2 6NU Free customer parking is available on-site. All collection orders must be placed online in advance. Orders are prepared manually by our warehouse team and must be picked, checked, packed, and transferred to the reception area, so collection is not immediate. Orders placed before 3:00pm are usually ready the same day. Orders placed after 3:00pm are normally prepared for next working day collection. Please do not travel to the collection point until you receive our “Ready to Collect” confirmation email. There is no Hi-Line signage on site. Simply go to the Big Yellow reception desk and provide your order name or number. Optional WhatsApp collection notifications: 075 9292 3131 (please message your order number) Collection hours: daily 10:30am–4:30pm Collection orders are treated as accepted at the point of collection. Support: [email protected]
Read moreLED Lightbox Lighting Explained
Choosing the correct lighting method for a lightbox is essential for achieving even illumination and long-term reliability. The two main approaches are edge-lit acrylic panels and back-lit lightboxes, and they are not interchangeable. Edge-lit lighting injects light into the acrylic edge and is ideal for very shallow constructions where edge access is available. For taller panels, edge lighting must be balanced, usually from both the top and bottom. If bottom edge access is not possible, uniformity cannot be guaranteed. In these cases, back-lighting is the correct solution. Back-lit lightboxes place LED modules behind the acrylic, projecting light forward into the cavity. This approach is particularly suitable for back-printed acrylic, larger panels, and installations where physical constraints prevent correct edge lighting. A common solution is the CL005 LED backlighting module, a 12V constant-voltage module designed specifically for signs and lightboxes. Modules can be cut to length and used up to 30 modules per electrical string, with larger layouts achieved using parallel wiring. Correct spacing, power supply headroom, and physical testing are all important to achieve a good result. In a recent example, a lightbox using 24 CL005 modules was powered by a 60W 12V LED driver, providing sufficient headroom for reliability and long service life. Using one driver per lightbox kept wiring simple and reduced thermal stress. For detailed wiring guidance, spacing recommendations, and a full case study, download our CL005 Installation Guide or contact the Hi-Line Lighting team for technical support.
Read more