High density RGBW (quad RGB+WW-96 LEDs/m) LED strip 23w/m 24V IP00 12mm/3oz 5m Roll
RGB+Warm White LED strip (Quad/4 in 1 Chip), RGB+2700K, 24V, IP00 (Non-Waterproof)
96 LEDs/m–24 W/m–1920Lm/m
5m roll–12mm width–3oz double layer PCB
5 year warranty
High Density commercial high-grade RGBW quad chip LED strip RGB+Warm White 96 LEDs/m 24V 23 w/m
23 w/m – 24V DC – 5m roll – 96 LEDs/m – IP00 (Non-Waterproof) – 5-wire cable (15cm on each side of the strip roll)
Our 12mm LED strips are powered by 3oz high copper flexible PCB, which makes it possible to maintain a cooler operating temperature despite very high brightness. This also ensures less voltage drop, which is useful for installations which require longer runs; up to 10m can be powered from one end only, without causing a noticeable reduction in brightness. Overall, 12mm results in a longer lifespan of the LED strip, with a consistently strong performance throughout.
This new design of RGBW LED strip integrates all 3 primary colours (Red/Green/Blue) + Warm White in a single chip. Due to this innovative design (4 in 1 chip), the strip is brighter than the conventional RGB + W strips, which have one chip for RGB and another one for white.
The RGBW LED strips are powered by high-quality quad RGBW SMD5050 LED chips. The brightness of each chip is 20 lumens (All colours together)
The power consumption is 24W per meter, which means an average of 6W per colour per meter.
The wavelength of R,G,B is as below:
R:620-625
G:520-525
B:465-470
For more information on RGB readings, please see our Wavelength Article.
Excellent colour rendering index (CRI) – all LED chips reach a value of Ra >80.
The strip can be cut at every 6.25cm. The width of the LED strip is 12mm.
Fitted with an easy to install original 3M adhesive tape with excellent adhesion.
5-year warranty
______________________________
The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.
Please do NOT connect more than 10 meters of a LED strip in series. A LED strip of more than 10 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Please note that 10m of this product can be installed in a single run with power only fed from one side. Thus, when 10 meters of the LED strip is exceeded (for up to 20m), it is suggested to connect the strip to a 24V DC power supply in the middle of the run (leaving 10 meters of the LED strip to the left and 10 meters to the right).
Please note that this data is based on the average readings for a 5-meter long LED strip. If the length of the strip is 1 meter the power consumption will be higher as there is almost no voltage drop.
______________________________
The RGBW LED strip comes with a 15cm wire ending on each side of the strip roll. Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).
Please note that soldering is recommended for the connection of LED strips.
______________________________
All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.
All Hi-Line RGB and RGBW LED strips are fully compatible with Fibaro RGBW LED Controller, Rako or ANY common anode LED controller available on the market. Crestron home automation system
______________________________
The stated price is for 1 x 5-meter roll RGBW LED strip (RGB + Warm White) with 480 SMD5050 RGBW LEDs – IP00 (Non-Waterproof), 24V DC.
______________________________
Note that, for driving RGBW LED Strips, you will have to combine the LED-Driver with an RGB/RGBW LED Controller.
In such case, LED driver is not required to be dimmable. Brightness control (dimming) and colour adjustment is still possible through the LED controller.
Installation hints and tips for LED strips can be downloaded at the bottom of this web page.
- CIE Colour Space
- 3 SDCM
- Voltage
- 24V DC
- Colour
- RGBW (RGB+WW)
- Power
- 23 w/m
- Brightness
- 1920 lm/m
- Number of LEDs per meter
- 96
- LED Strip Efficiency
- 80 lm/w
- Rating
- IP00 (Non-waterproof)
- Colour Temperature (CCT)
- RGB+2700K
- Colour rendering (CRI in ra)
- 80
- Width of strip
- 12mm
- FCP copper content
- 3 ounce double layer
- Cutting length
- Every 6.25cm (62.5mm)
- LED Strip Packing
- 5-meter roll
- Voltage Type
- Constant Voltage
- Warranty
- 5 Years
- Brand
- Hi-Line
- LED Chip
- Quad colour SMD 5050