Amber LED Strip 24V 9.6W/m-IP00-10mm wide-5m roll-SMD3528


New product

Amber LED strip, 24V, IP00

120 LEDs/m–9.6W/m

5m roll–10mm width (1.5mm height)

5-year warranty

More details

29 Items

Same Day Dispatch

£ 35,00

£ 7,00 per meter

Add to wishlist

Data sheet

LED Chip SMD 3528
CIE Colour Space 3 SDCM
Voltage 24V DC
Colour Amber
Power 9.6 W/m
Wavelength 604nm
Number of LEDs per meter 120
Rating IP00 (Non-waterproof)
Width of strip 10mm
Height of strip 3.5mm
Cutting length Every 6 LEDs (50mm)
LED Strip Packing 5-meter roll
Voltage Type Constant Voltage
Cable length 15cm
Warranty 5 Years
Brand Hi-Line

More info

Commercial high-grade Amber LED Strip non waterproof IP00

9.6W/m – 24V DC – 5m roll – 120 LEDs/m – IP00 – 2-wire cable (15cm on each side of the strip roll)

This LED strip is powered by high-quality Epistar SMD3528 LED chips 

The strip can be cut every 6 LEDs (5cm). The width of the LED strip is 10mm.

Fitted with an easy to install original 3M adhesive tape with excellent adhesion (identified by a red protective strip on the adhesive side).

*5-year warranty:

*This LED tape should be installed according to our installation instructions. For more information on installing, please see the installation manual at the bottom of the page and to learn more about the 5 year warranty on offer, please refer to the following link:

LED Strip Warranty Guide


The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.

Please do NOT connect more than 5 meters of a LED strip in series. A LED strip of more than 5 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Thus, when 5 meters of the LED strip is exceeded, it is suggested to connect the strip directly to the LED controller using a 2-core cable.

Installation hints and tips for LED strips can be downloaded at the bottom of this web page.


The LED strip comes with a 15cm wire ending on each side of the strip roll. Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).

Please note that soldering is recommended for the connection of LED strips. However, if a solder-free connection is preferred, Hi-Line’s solder-free connectors offer the best solution currently available on the market.


All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.


The stated price is for 1 x 5-meter roll LED strip (Amber) with 600 SMD3528 LEDs – IP00 (non-waterproof) 24V DC


Note that LED strips dimming is possible if the driver is used in combination with an LED controller. In such case LED driver is not required to be dimmable and brightness control (dimming) is still possible through the LED controller.

Selection of the LED driver depending on the maximum LED strip length

The table below shows the maximum LED strip length, which can be operated with a given LED driver.

To consider the performance drop, which occurs in the power supply cable and the efficiency of the LED Driver, 20% was deducted from the maximum strip length in the table below.


No customer reviews for the moment.

Write a review

Amber LED Strip 24V 9.6W/m-IP00-10mm wide-5m roll-SMD3528

Amber LED Strip 24V 9.6W/m-IP00-10mm wide-5m roll-SMD3528

Amber LED strip, 24V, IP00

120 LEDs/m–9.6W/m

5m roll–10mm width (1.5mm height)

5-year warranty

Customers who viewed this item also bought