High density natural white LED Strip 240 LEDs / meter CRI 80+
Naural White LED strip, 4000K, 24V, IP00 (Non-Waterproof)
5m roll–10mm width
CRI - Ra >80
5 year warranty
High Density LED strip 240 LEDs per meter 4000K
Natural White LED Strip 4000K, high density LED tape 240 LEDs per meter
19.2W/m – 24V DC – 5m roll – 240 LEDs/m – IP00 (Non-Waterproof) – 2-wire cable (15cm on each side of the strip roll)
This LED strip is powered by high-quality Epistar SMD3528 LED chips which generate a brightness of 1500Lm/m.
All LED chips reach a value of Ra >80.
At 240 LEDs per metre, this strip is able to eliminate shadows and create a continuous beam of light, which is improved further via our linear profiles. As such, 240 LED strips are also known as Spotless strips, ideal for anyone looking for a smooth, modern aesthetic.
Note: While any type of LED strip will perform better when installed in a profile or on an aluminium flat bar, due to the nature of high-powered SMD2835 chips running warm at 19.2 watts per metre and above, we strongly suggest that you consider installing this LED strip on an aluminium bar at the very minimum, in order to ensure proper cooling and thus increasing its lifespan. Always consult with your installer, as it may come down to their discretion, depending on how cool and well-ventilated the area is. Don’t risk burning out any chips!
The strip can be cut every 6 LEDs (25mm). The width of the LED strip is 10mm.
Fitted with an easy to install original 3M adhesive tape with excellent adhesion.
*This LED tape should be installed according to our installation instructions. For more information on installing, please see the installation manual at the bottom of the page and to learn more about the 5 year warranty on offer, please refer to the following link:
The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.
Please do NOT connect more than 5 meters of a LED strip in series. A LED strip of more than 5 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Thus, when 5 meters of the LED strip is exceeded, it is suggested to connect the strip directly to the LED controller or driver using a 2-core cable.
Installation hints and tips for LED strips can be downloaded at the bottom of this web page.
The LED strip comes with a 15cm wire ending on each side of the strip roll.Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).
NOTE: If cutting the strip into smaller pieces is required, then soldering is the only recommendation for reconnecting the 240 LED series.
Please see the following guide on how to efficiently cut this strip:
All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.
The stated price is for 1 x 5-meter roll LED strip (Natural White 4000K) with 1200 SMD3528 LEDs – IP00 (Non-Waterproof), 24V DC.
Note that LED strips dimming is possible if the driver is used in combination with an LED controller. In such case LED driver is not required to be dimmable and brightness control (dimming) is still possible through the LED controller.
- CIE Colour Space
- 3 SDCM
- 24V DC
- Natural White
- 19.2 W/m
- 1500 Lm/m
- Number of LEDs per meter
- IP00 (Non-waterproof)
- Colour Temperature (CCT)
- Colour rendering (CRI in ra)
- Width of strip
- Cutting length
- Every 6 LEDs (25mm)
- LED Strip Packing
- 5-meter roll
- Voltage Type
- Constant Voltage
- 5 Years
- LED Chip
- SMD 3528