Warm White LED Strip 5m roll | 24V | 9.6W/m | IP67 | CRI80 | 120 LEDs p/m
- Colour: Warm White LED
- Colour Temperature (CCT): 2700K
- Voltage: 24V DC
- IP Rating: IP67 (waterproof)
- LEDs per meter: 120
- Power: 9.6 Watts per Metre
- Brightness: 720-840Lm/m
- LED Strip Length: 5-meter roll
- Width of strip: 12mm
- CRI: Excellent - 80
- Warranty: 5 Year Warranty
Commercial High-Grade Warm White LED Strip 2700K
9.6W/m – 24V DC – 5m roll – 120 LEDs/m – IP67 (Waterproof) – 2-wire cable (15cm on each side of the strip roll)
This LED strip is powered by high-quality Epistar SMD3528 LED chips which generate a brightness of 720-840Lm/m.
Note: Should a higher brightness and efficiency LED strip be required, please check Hi-Line's SMD2835 LED strip series.
Excellent colour rendering index (CRI) – all LED chips reach a value of Ra >80.
The strip can be cut every 6 LEDs (5cm). The width of the LED strip is 12mm (including IP67 sleeve), pcb width is 10mm.
Fitted with an easy to install original 3M adhesive tape with excellent adhesion.
*This LED tape should be installed according to our installation instructions. For more information on installing, please see the installation manual at the bottom of the page and to learn more about the 5 year warranty on offer, please refer to the following link:
The high quality of Hi-Line LED strip products ensures low decay, which increases the LED strip's lifespan and assures that the high level of the brightness is kept constant throughout the LED strip's life.
Please do NOT connect more than 5 meters of a LED strip in series. A LED strip of more than 5 meters in length is overloaded due to the increased amount of current passing through, resulting in the damage of the PCB and the failure of the LED strip. Thus, when 5 meters of the LED strip is exceeded, it is suggested to connect the strip directly to the LED controller or driver using a 2-core cable.
Installation hints and tips for LED strips can be downloaded from the attachments tab.
The LED strip comes with a 15cm wire ending on each side of the strip roll. Therefore, no extra soldering is required if the roll should be cut into 2 different pieces (i.e. 3 meters + 2 meters).
Please note that soldering is recommended for the connection of LED strips.
All Hi-Line LED strips are dimmable. Please select a suitable PWM LED dimmer/controller to ensure the proper dimming of the LED strip.
The stated price is for 1 x 5-meter roll LED strip (Cool White) with 600 SMD3528 LEDs – IP67 (Waterproof), 24V DC.
Selection of the LED driver depending on the maximum LED strip length
The table below shows the maximum LED strip length, which can be operated with a given LED driver.
To consider the performance drop, which occurs in the power supply cable and the efficiency of the LED Driver, 20% was deducted from the maximum strip length in the table below.
Note that LED strips dimming is possible if the driver is used in combination with an LED controller. In such case LED driver is not required to be dimmable and brightness control (dimming) is still possible through the LED controller.
- 720-840 Lm/m
- CIE Colour Space
- 3 SDCM
- Warm White
- Colour rendering (CRI in ra)
- Colour Temperature (CCT)
- Cutting length
- Every 6 LEDs (50mm)
- LEDs per meter
- LED Chip
- SMD 3528
- LED Strip Length
- 5 meter roll
- 9.6 Watts per Metre
- IP Rating
- IP67 (Waterproof)
- 24V DC
- Voltage Type
- Constant Voltage
- 5 Years
- Width of PCB
- Width of strip